CWF
OIL Clear Wood Finish is a penetrating oil finish that provides deep
protection against moisture damage. When CWF OIL is first applied, the
wood will darken to a richer color, and then begin to lighten depending
on the intensity of sun exposure. CWF OIL finish provides a mildew-resistant
finish that protects and beautifies exterior wood.
BASIC
USES
• For exterior use only
• Weathered exterior woods including Cedar, Redwood and Pressure-Treated
Wood
• Horizontal and vertical surfaces such as decks, siding, fences,
furniture
• Do not use on roofing shakes or shingles, hardboard, plywood,
including T1-11 or over previously stained, varnished or painted wood
• Do not use in screened-in or enclosed areas
SURFACE
PREPARATION
GENERAL DIRECTIONS:
1. Surfaces must be thoroughly clean, dry and free of dirt, grease,
grime, mildew and previous coatings.
2. Remove mildew with a solution of 4 ounces of non-ammoniated detergent
(TSP), 1 quart of outdoor bleach and 3 quarts of fresh water. Allow
this solution to remain on the surface for 10-15 minutes, then rinse
thoroughly.
3. Clean weathered wood with Flood Wood Cleaner and Brightener, or Flood
Dekswood®.
4. Remove old finishes with Flood Wood Stripper or FloodPro® Stripper/Cleaner.
5. After cleaning, allow wood to dry 48 hours or until it has reached
a moisture content of 15% or less before finishing.
NEW
WOOD SURFACES:
New wood surfaces have a hard shiny surface called mill glaze that prevents
maximum penetration and bonding of a finish. To properly prepare the
surface for application, treat with a solution of Flood Wood Stripper,
diluted one quart per gallon of water. Test wood for absorbency by sprinkling
water on the surface. If water is absorbed rapidly, the surface is ready
for finishing.
WEATHERED
WOOD SURFACES:
Uncoated wood surfaces that have weathered longer than six months require
thorough cleaning before applying a finish. Use Flood Wood Cleaner or
Flood Dekswood (according to label instructions), along with a pressure
washer or stiff bristle brush to remove the loose fiber, dirt and other
surface contaminants.
PREVIOUSLY
COATED SURFACES:
Apply to bare wood surface or a weathered wood surface that was previously
finished with CWF OIL. Other previous stain, varnish or sealers must
be completely and thoroughly removed with Flood Wood Stripper or FloodPro
Stripper/Cleaner per label directions, before proceeding.
NOTE:
Cedar and Redwood may darken with Flood Wood Stripper or FloodPro Stripper/Cleaner.
If this occurs brighten with Flood Wood Cleaner or Flood Dekswood before
proceeding.
APPLICATION
TOOLS
• Brush: High quality, natural bristle stain brush
• Roller: 3/8”-3/4” lambs wool or mohair roller covers
• Spray: Air-Less sprayer .011 - .015 fluid tip/ 700-800 psi or
less
• Garden Sprayer
APPLICATION
CAUTION: Surfaces are slippery when wet. Use caution when walking on
wet surfaces during application.
1. Stir. Do not thin. Test color in small area.
2. Mix thoroughly before and periodically during application.
3. For color uniformity, intermix in one container, all stain to be
used on an entire section.
4. Cover everything you do not wish to coat, including plants and shrubs.
5. Apply between 50°F and 80°F.
6. Do not apply if cold and/or wet weather is expected within 48 hours.
7. Always work the entire length of a deck board or horizontal siding
to a logical break, such as a window or door frame.
8. Vertical siding should be coated from top to bottom.
9. Never stop application in the middle of the board or wall.
10. Never apply in direct sun light or hot surfaces.
11. For external use only, do not use indoors.
12. Two coats are recommended. Apply a second coat before the first
coat dries (usually within 20 minutes). Do not apply a second coat if
the first coat has dried.
13. After spray application, backbrush or backroll to improve penetration
and uniformity of coverage.
14. Wipe up any puddles to avoid shiny areas, (within 30 minutes).
NOTE:
Remember, CWF OIL is not a surface coating. It protects by penetrating
the wood providing a rich matte finish.
COVERAGE
• 100-200 sq. ft/gal (9.3-18.6 sq. m/gal)
• Coverage will vary depending on type, age and texture of wood
• On recoats you will need about half the materials you used the
first time
DECK
MAINTENANCE
• Most decks do not have to be coated every year
• A single coat of CWFOIL every second year will be sufficient
to refresh the natural beauty of your deck and to maintain protection
• Between recoats, a periodic cleaning with Flood Wood Cleaner
or Dekswood Cleaner and Brightener to remove dirt and contamination
will renew the appearance of the wood.
SIDING
MAINTENANCE
• CWF OIL renewal applications are touchup coats
• When coated areas turn gray, apply a coat of CWF OIL to replace
material which has weathered away
• Areas retaining good color do not need recoating
• Badly weathered areas may require 2 coats (apply the second
coat before the first coat dries)
• Backbrush or backroll to improve penetration and uniformity
of coverage
• Surfaces with harsh exposures to the sun and weather will show
wear more quickly than other areas. If this happens, clean effected
areas with Flood Wood Cleaner or Flood Dekswood and recoat as necessary,
blending into areas which still have good color. Areas retaining good
color do not need recoating.
CLEANUP
& STORAGE
• Mineral Spirits – If CWF OIL is allowed to dry on tools
it can be removed with paint remover
• Store unused portion in tightly closed container
• KEEP FROM FREEZING
