Commercial Grade Waterborne Wood Floor Finish
LNL-1500 Commercial Wood Floor Finish incorporates
Aluminum Oxide, Microban antimicrobial protection, and UV absorbers
in a single component non-yellowing urethane finish. Featuring a 15
Year Residential Wear Warranty, LNL1500 will prove superior durability,
with the added benefits of low odor, fast dry time and easy cleanup
Microban® protection continuously inhibits the growth of bacteria,
mold and mildew that can cause stains, odors, and damage the finish
on your floor. And because Microban® protection is built into this
coating, it will not wash off or wear away for the life of the finish.
Last•n•Last 1500 Wood Floor Finish is recommended for interior
Color in Container: Milky white (Dries clear)
Solids Content: 32+/-1%
Chemical Resistance: Excellent
VOC:VOC does not exceed 275grams/liter
Flash Point 198°F
Sheen Gloss: >80 units @ 60° on wood
Semi-Gloss: 50-60 units @ 60° on wood
Satin: 25-30 units @ 60° on wood
Freeze/Thaw Stability: Stable (if frozen, thaw completely before using)
Pot Life: Unlimited in unopened container
Dry Time: 2 to 3 hours with good conditions
Clean Up: Water
Application method: T- bar applicator, Synthetic waterborne applicator
and nylon brush.
Coverage: 400-450 sq. feet per gallon.
surface preparation is essential to achieve a high quality finish. Read
the MSDS sheet and wear proper protection, which may include gloves,
eye protection, and/or other protective devices.
New or Newly Sanded Floors or Wood Surfaces:Prepare the floor according
to NWFA or NOFMA accepted standard. The final pass before application
of Last•n•Last 1500 and sealer should be a #150 grit screen
pad or sandpaper. Remove dust completely by sweeping, vacuuming and
wiping the floor or work surface with a lint free cloth lightly dampened
with water. The floor or work surface and room temperature should be
at least 65°F.
Previously finished Floors or Wood Surfaces: Remove old finish in poor
condition. If the old finish is shellac or contains wax or any stearate,
regardless of the condition, remove it completely then follow surface
preparation for New Wood Surfaces. If old finish is still sound and
good, screen the work surface with a #150 screen disc, #180 grit sand
paper, maroon pad or similar. Remove dust completely by sweeping, vacuuming
and wiping the work surface with a lint free cloth lightly dampened
with water. The work surface and room temperature should be at least
65°F. Two to three coats work best on previously finished surfaces.
TO STIR THIS PRODUCT BEFORE AND DURING USE. LET IT STAND FOR 10 MINUTES
Apply in well ventilated area by nylon brush, or synthetic waterborne
applicator at room temperature and not in direct sunlight. Last•n•Last
1500 looks milky when applied, but will dry to a clear, beautiful finish.
Pou a 6-8” wide line of the finish along the starting wall. Apply
the finish with the grain of the wood. Using a clean pre-dampened waterborne
applicator, pull forward with the grain of the wood, moving the finish
towards the opposite wall. Holding the applicator at a snowplow angle
will maintain a wet edge at all times.( Maintain at least 3” wide
wet edge to ensure proper coverage). At the end of each run, turn the
applicator towards you and pad out the applicator parallel to the wet
edge. Feather out turns. If pushed too hard or fast, drips will fly
off the applicator. Missed areas can be touched up if seen right away.
To prevent lapping and dry marks, be sure you are using the recommend
coverage. Do no spread too thin. Screen the work surface in between
coats with any of the following #150 screen disc, #180 grit sand paper,
maroon pad or similar. Remember to vacuum and tack thoroughly after
screening to remove all dust. Allow minimum of two hours between coats,
or until thoroughly dry. Heavy finish application, high humidity or
lack of airflow will extend drying times. If waiting longer than 24
hours between coats, sanding is recommended.
over stain: Last•n•Last 1500 should adhere well to most
stain, but a test for adhesion over brands other than Last•n•Last
stain is recommended. Use Last•n•Last Classic Wood Stain
following instruction on label. Allow the stain to dry a minimum of
24 hours under good conditions. Make sure the stain is completely dry
before applying the finish or sealer.
When applied according to directions, and in thin coats, Last•n•Last
1500 should be dry to the touch in 1 hour. Allow minimum of 2 hours
between coats. Heavy finish application, high humidity or lack of airflow
will extend drying times. Last•n•Last 1500 completely cures
within 2 weeks. Please allow the finish to be fully cured for area rugs
or mats to be put down. The floor is susceptible to scuffing and marring
before full cure.
Use water to clean brushes and applicators.
Last•n•Last 1500 never needs waxing. We recommend Polycare
Floor Cleaner as the safe and effective cleaning product for all polyurethane
coated surfaces. It has a unique soap-free, no rinse formula which will
not harm polyurethane or varnished wood surfaces.