Search: Advanced search
 
Printable version 
Categories Categories
Shop by Brand
Paints & Stains
Painting Tools
Paint Remover & Strippers
Solvents/Cleaners
Patching Materials
Tapes & Adhesives
Paint Sprayers & Accessorios


Bestsellers Bestsellers
1. FLOOD FLD4 PENETROL SIZE:QUART.
2. FLOOD FLD6 FLOETROL SIZE:QUART.
3. FLOOD FLD6 FLOETROL SIZE:1 GALLON.
4. FLOOD FLD41 E-B EMULSA-BOND SIZE:QUART.
5. FLOOD 61820 FLOODPRO SPA-N-DECK BASECOAT SIZE:5 GALLONS.


Manufacturers Manufacturers
3M
Absolute Coatings
Advance Protective Products
Akzo Nobel Paints LLC
Allway Tools
American Safety Razor
ASM
Cabot Stain
Convenience Products
Daich Coatings

Other manufacturers...


Special Special
Gift certificates


Help Help
Contact us
Privacy statement
Terms & Conditions
Sitemap
About Us
Tips for Painting

Paint Store :: Shop by Brand :: Akzo Nobel Paints LLC :: FLOOD FLD447 CWF OIL CLEAR 350 VOC SIZE:5 GALLONS.

FLOOD FLD447 CWF OIL CLEAR 350 VOC SIZE:5 GALLONS.
FLOOD FLD447 CWF OIL CLEAR 350 VOC SIZE:5 GALLONS. 

CWF OIL Clear Wood Finish is a penetrating oil finish that provides deep protection against moisture damage. When CWF OIL is first applied, the wood will darken to a richer color, and then begin to lighten depending on the intensity of sun exposure. CWF OIL finish provides a mildew-resistant finish that protects and beautifies exterior wood.

BASIC USES
• For exterior use only
• Weathered exterior woods including Cedar, Redwood and Pressure-Treated Wood
• Horizontal and vertical surfaces such as decks, siding, fences, furniture
• Do not use on roofing shakes or shingles, hardboard, plywood, including T1-11 or over previously stained, varnished or painted wood
• Do not use in screened-in or enclosed areas

SURFACE PREPARATION
GENERAL DIRECTIONS:

1. Surfaces must be thoroughly clean, dry and free of dirt, grease, grime, mildew and previous coatings.
2. Remove mildew with a solution of 4 ounces of non-ammoniated detergent (TSP), 1 quart of outdoor bleach and 3 quarts of fresh water. Allow this solution to remain on the surface for 10-15 minutes, then rinse thoroughly.
3. Clean weathered wood with Flood Wood Cleaner and Brightener, or Flood Dekswood®.
4. Remove old finishes with Flood Wood Stripper or FloodPro® Stripper/Cleaner.
5. After cleaning, allow wood to dry 48 hours or until it has reached a moisture content of 15% or less before finishing.

NEW WOOD SURFACES:
New wood surfaces have a hard shiny surface called mill glaze that prevents maximum penetration and bonding of a finish. To properly prepare the surface for application, treat with a solution of Flood Wood Stripper, diluted one quart per gallon of water. Test wood for absorbency by sprinkling water on the surface. If water is absorbed rapidly, the surface is ready for finishing.

WEATHERED WOOD SURFACES:
Uncoated wood surfaces that have weathered longer than six months require thorough cleaning before applying a finish. Use Flood Wood Cleaner or Flood Dekswood (according to label instructions), along with a pressure washer or stiff bristle brush to remove the loose fiber, dirt and other surface contaminants.

PREVIOUSLY COATED SURFACES:
Apply to bare wood surface or a weathered wood surface that was previously finished with CWF OIL. Other previous stain, varnish or sealers must be completely and thoroughly removed with Flood Wood Stripper or FloodPro Stripper/Cleaner per label directions, before proceeding.

NOTE: Cedar and Redwood may darken with Flood Wood Stripper or FloodPro Stripper/Cleaner. If this occurs brighten with Flood Wood Cleaner or Flood Dekswood before proceeding.

APPLICATION TOOLS
• Brush: High quality, natural bristle stain brush
• Roller: 3/8”-3/4” lambs wool or mohair roller covers
• Spray: Air-Less sprayer .011 - .015 fluid tip/ 700-800 psi or less
• Garden Sprayer

APPLICATION
CAUTION: Surfaces are slippery when wet. Use caution when walking on wet surfaces during application.
1. Stir. Do not thin. Test color in small area.
2. Mix thoroughly before and periodically during application.
3. For color uniformity, intermix in one container, all stain to be used on an entire section.
4. Cover everything you do not wish to coat, including plants and shrubs.
5. Apply between 50°F and 80°F.
6. Do not apply if cold and/or wet weather is expected within 48 hours.
7. Always work the entire length of a deck board or horizontal siding to a logical break, such as a window or door frame.
8. Vertical siding should be coated from top to bottom.
9. Never stop application in the middle of the board or wall.
10. Never apply in direct sun light or hot surfaces.
11. For external use only, do not use indoors.
12. Two coats are recommended. Apply a second coat before the first coat dries (usually within 20 minutes). Do not apply a second coat if the first coat has dried.
13. After spray application, backbrush or backroll to improve penetration and uniformity of coverage.
14. Wipe up any puddles to avoid shiny areas, (within 30 minutes).

NOTE: Remember, CWF OIL is not a surface coating. It protects by penetrating the wood providing a rich matte finish.

COVERAGE
• 100-200 sq. ft/gal (9.3-18.6 sq. m/gal)
• Coverage will vary depending on type, age and texture of wood
• On recoats you will need about half the materials you used the first time

DECK MAINTENANCE
• Most decks do not have to be coated every year
• A single coat of CWFOIL every second year will be sufficient to refresh the natural beauty of your deck and to maintain protection
• Between recoats, a periodic cleaning with Flood Wood Cleaner or Dekswood Cleaner and Brightener to remove dirt and contamination will renew the appearance of the wood.

SIDING MAINTENANCE
• CWF OIL renewal applications are touchup coats
• When coated areas turn gray, apply a coat of CWF OIL to replace material which has weathered away
• Areas retaining good color do not need recoating
• Badly weathered areas may require 2 coats (apply the second coat before the first coat dries)
• Backbrush or backroll to improve penetration and uniformity of coverage
• Surfaces with harsh exposures to the sun and weather will show wear more quickly than other areas. If this happens, clean effected areas with Flood Wood Cleaner or Flood Dekswood and recoat as necessary, blending into areas which still have good color. Areas retaining good color do not need recoating.

CLEANUP & STORAGE
• Mineral Spirits – If CWF OIL is allowed to dry on tools it can be removed with paint remover
• Store unused portion in tightly closed container
• KEEP FROM FREEZING

 
   

  47%

Details
 
SKU 1027344720
Quantity in stock 1000 item(s) available
Weight 61.00 lbs
Retail Price: $253.98
Our Price: $133.34

Options
 
Quantity

Add to cart
        


 

Send to friend
Your name: *
Your e-mail: *
Recipient's email: *

Type the characters you see in the picture. (If you do not see any picture here, please enable images in your web browser options and refresh this page):

Get a different code
The code is case-sensitive and must be entered exactly as above.

Send to friend
 

Detailed images
FLOOD FLD447 CWF OIL CLEAR 350 VOC SIZE:5 GALLONS.
 

Recommended products list
Customers who bought this product also bought the following products:  

 
 

Your cart Your cart
Cart is empty
 

View cart
Checkout
Orders history


Authentication Authentication
Username

Password

Log in 
Register 
Recover password

If Javascript is disabled in your browser click here


News News


 


Popular Categories

Tapes

Spray Paint

Paint Brushes

Paint Tools

Caulk and Sealants

Paint Remover & Stripper

Hand Tools

Interior Paint

Exterior Paint

 

Popular Brands

ZAR

Valpar

Cabot

DAP

3M

ASM

 

Hammerite

Modern Masters

 

Best Seller Products

Duct Tape

Black Paint

White Paint

Blue Paint

Red Paint

Dap Plus

Chalk Board Paint

Gold Paint

Aluminum Paint

 
 

We accept major credit cards

credit cards logo
 
Home | Store | About Us | Search | Terms & Conditions | Privacy Statement | Contact Us | Directory | Site Map | News | Paint Store Blog
 
SEO by site SEO
 
 

CONNECT WITH US
Copyright 2005-2015 Paint Store - All Rights Reserved